background image

PARTS TO BE INSTALLED

tsi2011-014-006_a

TYPICAL

1. Open clamp
2. Side cage tube

6. Secure sport visor with k50 screws into clamps.

TORQUE

Sport visor screws

2.5 N•m (22 lbf•

in

)

Rear Wind Screen (LTD Models)

REQUIRED PARTS

QTY

Rear wind screen

1

Rear wind screen installation kit

(from predelivery box #1)

1

1. Unfold rear wind screen.

2. Install the upper middle straps loosely around

the rear upper cage tube to support the rear
wind screen.

3. On both sides, secure the second strap below

seat belt attachment point and the third strap
above this point, as shown on the following il-
lustration.

tbl2012-003-018_a

1. Seat belt attachment point
2. Second strap
3. Third strap

4. Attach all remaining straps to cage tube.

5. Secure rear wind screen hooks at the bottom of

the seat belt mechanism attachment plate.

tbl2012-003-019_a

1. Rear net hook

6. Pull hook straps tight.

7. Secure lower section of rear wind screen.

7.1 Remove the top middle screw, metallic flat

washer and nut from the rear bulkhead.

7.2 Using previously removed fasteners, se-

cure the bottom of the rear wind screen
against the bulkhead. Install the new plas-
tic washer (from the rear net installation
kit) between rear wind screen and screw
head.

7.3 Tighten screw to specification.

TORQUE

Bulkhead screw

10 N•m (89 lbf•

in

)

Roof Middle Section (LTD
Models)

REQUIRED PARTS

QTY

Roof middle section

1

Roof middle section installation kit

(from predelivery box #1)

1

1. Install roof middle section upside down on a

smooth non abrasive surface.

2. Clean seal groove with isopropyl alcohol.

3. Install neoprene seal into groove located to-

ward front of top. Cut extra length if needed.

26 / 54

2014-2

PREDELIVERY

Содержание Can-Am Commander 1000 DPS 2014























































Отзывы: