Brother PR1055X Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 200

background image

16

Setup and transporting precautions

30.

Magnetic frame

50 mm (W) x 50 mm (H)

(2 inches (W) x 2 inches (H))

PRMH50 (Americas)
PRMF50: XG8597-001 (Europe)
PRMF50AP: 115D02E700F (other areas)

31.

Scan frame set

PRSCANFKIT1: XG8237-001 (Europe)
PRSCANFKIT1AP: 115D02E700D (other
areas)

32.

Tubular frame table

PRTT1 (Americas)
PRTT1: D01FAF-001 (Europe)
PRTT1AP: 115K02E7002 (other areas)

33.

Embroidery Stand

PRNSTD2 (Americas)
VRPRNSTD: XG3199-001 (Europe)
VRPRNSTDCN: 115Z05E6005 (China)
VRPRNSTD: 115Z05E7005 (other areas)

34.

Metal bobbin

100376-051

35.

Weight (S)

XC6631-051

36.

Embroidery positioning sticker sheets

× 8

SAEPS2 (U.S.A.) / SAEPS2C (Canada)
EPS2: XG6749-001 (Europe)
EPS2CN: 115Z05E600E (China)
EPS2: 115Z05E700E (other areas)

Note

• Visit your nearest authorized Brother dealer for a

complete listing of optional accessories and
embroidery cards available for your machine.

Memo

• Always use accessories recommended for this

machine.

• All specifications are correct at the time of printing.

Please be aware that some specifications may
change without notice.

Part Name

Part Code

SETTING UP THE MACHINE

CAUTION

• The temperature of the operating environment

should be between 5 °C (40 °F) and 40 °C
(104 °F). If the machine is operated in an
environment that is either too cold or too hot,
the machine may malfunction.

• Do not use the machine in a location where it

will be exposed to direct sunlight, otherwise
the machine may malfunction.

• Set up the machine with it’s four adjustable

feet completely in contact with the desk or
table, so that the machine is level.

• Do not put anything under the machine that

could block the ventilation slots found on the
rear underside of the machine, in order to
avoid the possibility of the machine’s motor
overheating, resulting in a fire or in damage to
the machine.

• The machine weight is approximately 41.8 kg

(92 lb). The transporting or setting up of the
machine should be performed by two people.

• When transporting the machine, be sure to

have two people lift the machine from the
bottom at the indicated slots (

1

). Lifting the

machine from any other area may damage the
machine or result in the machine falling, which
could cause injuries.

• When lightning occurs, turn off the machine

and unplug the power supply cord. Lightning
may cause the machine to malfunction.

• Do not plug in the power supply cord until

setup of the machine is completed, otherwise
injuries may result if the “Start/Stop” button is
accidentally pressed and the machine starts
embroidering.

«
...
16
17
18
19
20
...
»

Содержание PR1055X









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PR1055X

Бренд: R.P.S. Corporation Страницы: 48

Бренд: Banner Страницы: 11

Бренд: Antari Страницы: 10

Бренд: Neopost Страницы: 6

Бренд: Lindhaus Страницы: 25

Бренд: Windsor Страницы: 25

Бренд: Sagem Страницы: 44

Бренд: Briteq Страницы: 8

Бренд: A-S-S Страницы: 7

Бренд: Tennant Страницы: 41

Бренд: MIMAKI Страницы: 5

Бренд: Fellowes Страницы: 94

Бренд: JUKI Страницы: 4

Бренд: JUKI Страницы: 7

Бренд: JUKI Страницы: 18

Бренд: JUKI Страницы: 40

Бренд: Crane Страницы: 50

Бренд: Oki Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды