Brother PR1055X Скачать руководство пользователя страница 178

Страница: 178 / 200

176

■

Disassembling and cleaning the tension unit

To remove tension dial, turn dial counterclockwise as
shown on illustration.

Tension dial

Using the included cleaning brush, remove any lint and
dust from the two pieces of felt washers (top, bottom)
inside the tension dial.

Tension dial

Nylon shoulder washer

Tension spring

Tension base spring

Felt washer (top)

Tension disc

Felt washer (bottom)

Reassembling the tension unit.

Replacing the needle

Set the main power switch to “O” to turn off the
machine.

Loosen the needle set screw and remove the needle.

Hold the needle with your left hand, and then hold the
Allen screwdriver in your right hand and turn the needle
set screw counterclockwise.

Note

• When reassembling the tension unit, be sure not to

install the tension disc upside-down.
There is a magnet on the bottom.

Bottom

Top

Magnet

• When reassembling the tension unit, be careful not

to lose any parts or install any parts in an incorrect
order. The machine may not operate correctly if the
tension units are incorrectly reassembled.

CAUTION

• Be sure to turn off the machine before

replacing the needle, otherwise injuries may
result if the machine starts embroidering.

• Your machine is designed to use household

embroidery needles. The factory
recommended needle is “HAX 130 EBBR”
(Organ). Schmetz needles 130/705 H-E may
be used as a substitute.

• Never use bent needles. Bent needles can

easily break, possibly resulting in injuries.

Memo

• To check the needle correctly, place the flat side of

the needle on a flat surface. Check the needle from
the top and the sides. Throw away any bent
needles.

Parallel space

Flat surface (glass, etc.)

Note

• Be sure to use the included Allen screwdriver to

replace the needle.

Содержание PR1055X









































































































































































































Результаты поиска

Содержание PR1055X

Отзывы:

Похожие инструкции для PR1055X

Бренды по названию

Популярные бренды

Brother PR1055X, Руководство по эксплуатации

Результаты поиска

Содержание PR1055X

Отзывы:

Похожие инструкции для PR1055X

Бренды по названию

Популярные бренды