Brother PR1055X Скачать руководство пользователя страница 119

Страница: 119 / 200

ADVANCED EMBROIDERY

117

As shown in the illustration, hold the bobbin case
against a smooth vertical surface.

• If the thread with the weight attached is slowly pulled

out, the thread tension is correct.

Use the included standard screwdriver to turn the
tension-adjusting screw and adjust the thread tension.

After making the adjustments, try embroidering with
all needle bars to check the thread tension.

Tension-adjusting
screw

Tighter

Looser

Memo

• In the built-in embroidery patterns, one pattern is

used for checking the thread tension. By
embroidering this pattern, the thread tension can
easily be checked. From the wrong side of the
fabric, the bobbin thread should be adjusted to be
about one third of the stitch width.

Содержание PR1055X









































































































































































































Результаты поиска

Содержание PR1055X

Отзывы:

Похожие инструкции для PR1055X

Бренды по названию

Популярные бренды

Brother PR1055X, Руководство по эксплуатации

Результаты поиска

Содержание PR1055X

Отзывы:

Похожие инструкции для PR1055X

Бренды по названию

Популярные бренды