Brother HL-5250DN series Скачать руководство пользователя | Manualshive

Страница: 13 / 337

background image

HL-5240/5250DN/5270DN/5280DW SERVICE MANUAL

xi

Confidential

DEFINITIONS OF WARNINGS, CAUTIONS AND NOTES

The following conventions are used in this service manual:

WARNING

Indicates warnings that must be observed to prevent possible personal injury.

!

CAUTION:

Indicates cautions that must be observed to service the printer properly or prevent
damage to the printer.

NOTE:
Indicates notes and useful tips to remember when servicing the printer.

**Listed below are the various kinds of “WARNING” messages included in this manual.

WARNING

Always turn off the power switch and unplug the power cord from the power outlet
before accessing any parts inside the printer.

WARNING

Some parts inside the printer are extremely hot immediately after the printer is
used. When opening the front cover or back cover to access any parts inside the
printer, never touch the shaded parts shown in the following figures.

WARNING

If you analyze malfunctions with the power plug inserted into the power outlet,
special caution should be exercised even if the power switch is OFF because it is a
single pole switch.

WARNING

DO NOT use any type of spray to clean inside or outside of the machine. Doing this
may cause a fire or electrical shock.

«
...
11
12
13
14
15
...
»

Содержание HL-5250DN series


















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-5250DN series

Бренд: IBM Страницы: 908

Бренд: Omneon Страницы: 2

Saddle Finisher-AF2

Бренд: Canon Страницы: 244

Бренд: Star Страницы: 24

Бренд: Parkside Страницы: 176

Бренд: NAIM Страницы: 18

N2400 - TaskSmart - 1 GB RAM

Бренд: Compaq Страницы: 372

Бренд: U-Line Страницы: 33

Бренд: Exsys Страницы: 24

Бренд: Oki Страницы: 4

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

Бренд: Xiamen Hanin Electronic Technology Страницы: 27

Бренд: LaserLine Страницы: 14

Бренд: Oki Страницы: 182

System x3650 M5

Бренд: IBM Страницы: 1010

Бренд: IBM Страницы: 98

7400DN - Phaser Color LED Printer

Бренд: Xerox Страницы: 3

NanoPrint LM210

Бренд: Arrayit Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды