manualshive.com logo in svg

Brother HL-5250DN series, Руководство по обслуживанию

Поделиться
Скачать
Brother HL-5250DN series Скачать руководство пользователя страница 63

CHAPTER 3 PERIODIC MAINTENANCE 

Confidential 

3-2

<Toner Low Message> 

(HL-5240/5250DN)

 

The 

Toner

 LED alternates turning on for 2 seconds and off for 3 seconds.  

 

Fig. 3-1 

If the LED shows this message, the printer has nearly run out of toner.  Buy a new toner  
cartridge and have it ready before you get a “Toner Life End” message. 

NOTE:  
The 

Toner 

LED will blink continuously if the toner cartridge is nearly empty. 

(HL-5270DN/5280DW) 

Appears at intervals. 

TONER LOW

 

If the LCD shows “TONER LOW”, the printer has nearly run out of toner.  Buy a new toner  
cartridge and have it ready before you get a “TONER LIFE END” message.  

 

<Toner Life End Message> 

(HL-5240/5250DN)

 

If the LED shows the message below, the printer has run out of toner or the toner is not  
evenly distributed inside the cartridge. 

 

Fig. 3-2 

(HL-5270DN/5280DW) 

Appears at intervals. 

TONER LIFE END

 

If the LCD shows “TONER LIFE END”, the printer has run out of toner or the toner is not 
evenly distributed inside the cartridge.  

In both situations, the printer will stop printing until a new toner cartridge has been put into 
the printer.  “TONER LIFE END” can only be cleared by putting a new toner cartridge into 
the drum unit. 

Содержание HL-5250DN series


















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды