Brother HL-5250DN series Скачать руководство пользователя

Страница: 158 / 337

CHAPTER 4 TROUBLESHOOTING

Confidential

4-44

(I-6) Black and blurred vertical streaks

Possible cause

Step

Check

Result

Remedy

Corona failure

Is the corona wire dirty?

Yes

Clean the corona wire with the
wire cleaner.

Corona failure

Is the vertical block streak
about 10mm wide?
(Check if the wire cleaner is at
its home position.)

Yes

Return the wire cleaner to its
home position.

Dirt in the paper
feed system

Is the paper tray or feed
system on the drum unit dirty
with toner?

Yes

Clean the toner off.

Scratch on the
drum

Is the surface of the drum
scratched?

Yes

Replace the drum unit.

Cleaning failure

Is the surface of the drum dirty
with toner in streaks?

Yes

Replace the drum unit.

Scratch on the
heat roller

Is the surface of the heat roller
scratched?

Yes

Replace the fuser unit.

NOTE:

•

If you print the same pattern (especially vertical streaks) continuously, electrostatic charge
performance of the drum will decrease temporarily and black vertical streaks may appear
on the paper.

•

This problem may occur with noise due to the corona wire being dirty. In that case, clean
the corona wire with the wire cleaner.

User Check

(1) Clean the corona wire in the drum unit.

(2) Check that the wire cleaner is at the home position.

(3) Check that the toner cartridge is not empty.

(4) The drum unit may be damaged. Install a new drum unit.

(5) The toner cartridge may be damaged. Install a new toner cartridge.

Содержание HL-5250DN series


















































































































































































































































































































































Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды

Brother HL-5250DN series, Руководство по обслуживанию

Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды