Brother HL-5250DN series Скачать руководство пользователя | Manualshive

Страница: 126 / 337

background image

CHAPTER 4 TROUBLESHOOTING

Confidential

4-12

2.3

Error Message in the Status Monitor

The Status Monitor will report problems with the printer. Take the corrective actions listed in
the following table for the error message that the Status Monitor reports.
The default setting for the Status Monitor is off. If you would like to turn the status monitor on,
you can change the setting of the Status Monitor in the

Device Options

of the

Advanced

tab.

Error message

Remedy

Toner Low

•

Purchase a new toner cartridge and have it ready for when the

Toner Life End status is indicated.

Toner Life End

•

Refer to

1.1 “Toner Cartridge” in Chapter 3.

Cartridge Error

•

Take out the toner cartridge and put it back into the printer again.

Drum Near End

•

The drum is near the end of it's life. Purchase a new drum unit to

replace the current one. Refer to

1.2 “Drum Unit” in Chapter 3.

No Paper Fed Tray
No Paper Fed Manual
No Paper Multi
Purpose Tray
No Paper Tray 1/2/3

•

The paper tray may be out of paper or not properly installed. If it

is empty, put a new stack of paper in the paper tray and then
press the

Go

button.

•

If there is paper in the paper tray, make sure it is straight. If the

paper is curled, straighten it before printing. Sometimes it is
helpful to remove the paper, turn the stack over and put it back in
the paper tray.

•

Reduce the amount of paper in the paper tray, and then try

again.

•

Make sure you use paper that meets Brother’s recommended

paper specifications. Refer to

3.6 “Paper” in Chapter 1.

Jam MP Tray
Jam Tray 1/2/3
Jam Inside
Jam Rear
Jam Duplex

•

Take out the jammed paper from the indicated area.
Refer to

3.2 “Paper Jams” in this Chapter.

Incorrect Paper Size
for DX

•

Press the

Go

button or

Job Cancel

button. Set the correct paper

that you want to use, or load the same size paper that you
selected in the current driver setting. The paper size you can use
for automatic duplex printing is A4, Letter or Legal.

Duplex Disabled

•

Close the back cover of the printer and put the duplex tray back

in.

Front cover open

•

Close the front cover of the printer.

Fuser cover open

•

Close the fuser cover located behind the back cover of the

printer.

Fig. 4-2

«
...
124
125
126
127
128
...
»

Содержание HL-5250DN series


















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-5250DN series

Бренд: idp Страницы: 88

Бренд: Wang Страницы: 24

x3655 - System - 7985

Бренд: IBM Страницы: 118

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 23

Бренд: ACTi Страницы: 15

BladeCenter PN41

Бренд: IBM Страницы: 88

Бренд: HPE Страницы: 174

Бренд: EFI Страницы: 4

Eserver 345 Series

Бренд: IBM Страницы: 70

Бренд: Xblue Networks Страницы: 42

Blaster ADVANTAGE

Бренд: CognitiveTPG Страницы: 20

DocuColor 45087638

Бренд: Xerox Страницы: 28

BladeCenter PS703

Бренд: IBM Страницы: 198

Бренд: GCC Technologies Страницы: 80

Бренд: ZKTeco Страницы: 38

Бренд: HP Страницы: 38

ProLiant DL320 Generation 4

Бренд: HP Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды