Brother HL-5250DN series Скачать руководство пользователя

Страница: 65 / 337

CHAPTER 3 PERIODIC MAINTENANCE

Confidential

3-4

(3) Push down the blue lock lever and take the toner cartridge out of the drum unit.

Fig. 3-5

CAUTION:

* Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash

it off with cold water at once.

* To avoid any degradation of the print quality, DO NOT touch the shaded parts shown in the

illustrations.

NOTE:
* Be sure to seal up the toner cartridge tightly in a bag so that toner powder does not spill out

of the cartridge.

* Discard the used toner cartridge according to local regulations, keeping it separate from

domestic waste. If you have questions, call your local waste disposal office.

(4) Unpack the new toner cartridge. Hold the cartridge level with both hands and gently rock it

from side to side five or six times to spread the toner evenly inside the cartridge.

Fig. 3-6

Содержание HL-5250DN series


















































































































































































































































































































































Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды

Brother HL-5250DN series, Руководство по обслуживанию

Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды