Brother HL-5250DN series Скачать руководство пользователя

Страница: 128 / 337

CHAPTER 4 TROUBLESHOOTING

Confidential

4-14

2.4

Error Message Printouts

The printer will report problems by printing an error message as defined in the following table.
Take the corrective actions for the error message.

Error message

Remedy

MEMORY FULL

•

Press the

button to print the data left in the printer.

Cancel the print job if you want to delete the data
remaining in the printer.

•

Reduce the print resolution or reduce the complexity of

your document.

•

Add more memory.

PRINT OVERRUN

•

Press the

button to print the data left in the printer.

Cancel the print job if you want to delete the data
remaining in the printer.

•

If this does not clear the error, reduce the complexity of

your document or reduce the print resolution.

•

Add more memory.

•

Set page protection to

AUTO

by using the supplied

Windows

driver or Remote Printer Console program.

•

Change the following settings in the supplied Windows

driver and try again. The best combination of these
settings will vary depending on your document:

•

Graphics Mode

•

TrueType mode

•

Use Printer TrueType

Fonts

RESOLUTION REDUCED TO
ENABLE PRINTING
(The printer has printed the
document at a reduced
resolution)

•

Reduce the complexity of your document before you print
to prevent automatic reduction in the resolution.

* NOTE:

The communication parameter settings are printed on the Print Settings sheet. For details on
how to print the Print Settings page, refer to

“Print Settings” in Chapter 7

Содержание HL-5250DN series


















































































































































































































































































































































Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды

Brother HL-5250DN series, Руководство по обслуживанию

Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды