Broderson IC-200-2H Скачать руководство пользователя

Страница: 9 / 74

1-5

SECTION 1

DESCRIPTION AND SPECIFICATIONS

The IC-200-H is a self-propelled Industrial Crane designed for material handling and

installation, maintenance and repair of equipment, with special features of self-loading

cargo decks, 4-wheel steer, and f ront-wheel drive (4-wheel drive optional). T he basic

unit consists of a chassis and hydraulic boom assembly. The chassis includes a f rame,

four hydraulic independently controlled outriggers, engine, torque converter, powershift

4-speed transmission, front planetary drive/steer axle and rear steer-only axle, fuel tank,

hydraulic tank, control station, power steering and dual pow er brakes. T he boom

assembly includes a hy draulic powered continuous rotation turret, 3 or 4-section

telescopic boom, hydraulic boom elevating cylinder, hydraulic boom telescope cylinders

and hydraulic powered hoist. A Rated Capacity Limiter is standard.

IC-200-2H:

3-section hydraulically extended boom with capacity of 30,000 pounds (13600 kg) at

a 6-foot (1.8 m) load radius. Horizontal reach of 36 feet (11.0 m) and vertical reach

of 45 feet (13.7 m).

IC-200-3H:

4-section proportional hydraulically extended boom with capacity of 30,000 pounds

(13600 kg) at a 6-foot (1.8 m) load radius. Horizontal reach of 50 feet (15.2 m) and

vertical reach of 58 feet (17.7 m).

General:

IC-200-2H

IC-200-3H

Weight:

Front Axle

13,960 pounds (6340 kg)

15,390 pounds (6,990 kg)

Rear Axle

14,540 pounds (6600 kg)

15,690 pounds (7,120 kg)

Total

28,500 pounds (12940 kg) 31,080 pounds(14,110 kg)

Length:

Overall

22 feet 6 inches (6.86 m)

22 feet 10 inches (6.96 m)

Chassis

14 feet 11 inches (4.55 m) 14 feet 11 inches (4.55 m)

Width:

7 feet 10.5 inches (2.40 m)

Height:

Overall

8 feet (2.45 m)

Deck

47 inches (1.19 m)

Wheelbase:

97 inches (2.46 m)

Ground Clearance:

11 inches (349 mm)

Angle of Approach:

degrees

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды