Broderson IC-200-2H Скачать руководство пользователя

Страница: 71 / 74

3-27

COOLING SYSTEM:

Check the level of coolant in the radiator overflow tank daily. Add a mixture of antifreeze and

distilled water to the overflow tank as required to maintain the coolant level. Check the radia-

tor fins for dirt or debris daily and wash the fins with a pressure or steam cleaner every 50

hours or as required. Check the antifreeze protection level every 500 hours. Every 2 years,

flush the cooling system and replace the thermostat and coolant. Pressure test the system as

specified by the engine manufacturer.

SPARE PARTS LIST:

A spare parts list (including oil filter, fuel filter, etc.) may be found in the Parts Manual, under

Engine Installation.

MAJOR ENGINE SERVICING OR OVERHAUL:

Major servicing or overhaul is beyond the scope of this manual. Consult authorized engine

service manual or rely on an authorized engine service center

MECHANICAL ADJUSTMENTS

FASTENERS:

All fasteners on t he IC-200 should be check ed and retightened if required, as a part of the

preventive maintenance program. Particular attention should be given to the drive axle mount-

ing bolts, pump mounting bolts, pump drive shaft bolts, rotation bearing bolts, rotation gearbox

bolts, winch bolts, etc. All bolts used in assembly are heat-treated Grade 5 or 8. Torque the

rotation bearing mounting bolts (3/4",Gr. 8) to 325 foot-pounds (440 Nm), or the nuts to 325

foot-pounds (440 Nm). Torque the wheel nuts to 500 foot-pounds (678 Nm). The torque chart

on the next page can be used on all other bolts.

ROTATION GEARBOX:

The rotation gearbox assembly is attached to the chassis top plate by four capscrews. It is

held in proper engagement with the external teeth on the bull gear by two setscrews. It is fur-

ther restrained from torsional movement by two bolts on each side of the gearbox mounting

flange. The gearbox should be adj usted with the boom centered over front of the chassis.

This centers the gearbox pinion on the “high side” of the bearing gear teeth. Adjust the gear-

box inward until there is “light contact” between pinion and bull gear teeth. Retighten the four

mounting bolts and the four side bolts.

TRANSMISSION AND AXLE TROUBLESHOOTING AND OVERHAUL:

Procedures for transmission and axle troubleshooting and overhaul are beyond the scope of

the BMC Maintenance and Par ts Manuals. I nternational Transmission Ltd. factory service

manuals are available from BMC as follows:

Transmission Service Manual, BMC Part Number 990-00021

Axle Service Manual, BMC Part Number 990-00020

PARK BRAKE TEST AND ADJUSTMENT:

1. Fully apply the parking brake.

2. Start the engine, retract the boom to the appropriate traveling position and raise the out-

riggers.

3. Select fourth gear.

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды