Broderson IC-200-2H Скачать руководство пользователя

Страница: 63 / 74

3-19

HYDRAULIC OILS FOR IC-200

AMBIENT TEMP RANGE: -40° to 75°F

-15° to 110°F

50° to 130°F

(-40° to 24°C)

(-26° to 43°C)

(10° to 54°C)

POUR POINT:

-40°F MAX

-15°F MAX

0°F MAX

(-40°C)

(-26°C)

(-18°C)

VISCOSITY INDEX:

140 MIN

95 to 100

VISC. SSU @ 100°F (38°C): 200 MAX

230 MAX

340 MAX

SSU @ 210°F (100°C):

44 MIN

47 MIN

53 MIN

EXAMPLES:

MOBIL DTE-13

MOBIL AW-46

MOBIL AW-68

MOBIL UNIV.-ATF

MOBIL DTE-25

MOBIL DTE-26

TEXAMATIC TYPE F CONOCO SUPER 46 CONOCO SUPER 68

TEXACO HD 46

TEXACO HD 68

OTHER REQUIREMENTS: M ust contain rust and ox idation inhibitor, and antifoam and

antiwear agents. Must pass Vickers Vane Pump Test.

The IC-200 is factory filled with hydraulic oil for the -15° to 110°F (-26° to 43°C) range. If sig-

nificant portions of time are spent operating below 20°F (-7°C) or above 100°F (43°C), the oil

should be replaced with an extreme temperature oil.

The oils shown are compatible with and may be combined with SAE 10W or SAE 20W-20 mo-

tor oil if it is necessary to add oil between changes and the recommended oils are not availa-

ble. These motor oils are not suitable substitutes when changing hydraulic oil because t hey

lack certain additives that are needed for hydraulic system use.

C A U T I O N

Never add kerosene or other "thinners" to hydraulic oil. These fluids have low aniline
points and consequently will cause rapid deterioration of certain packings and seals in
the hydraulic system.

C A U T I O N

Serious damage to the pump will result if it is run with the shutoff valve closed or with
insufficient oil level in the reservoir.

Observe the operation of the machine. If the oil is too cold, the machine will be sluggish and

should be warmed up further to prevent damage before sustained hard work is attempted. If

the oil is too hot, leakage will increase, pump efficiency will go down, and moving parts will not

be properly lubricated. If operating temperature is excessive, rapid deterioration of the oil will

result and m oving parts and seals w ill wear more quickly. The cause of the excess heat

should be determined and corrected. A possible indicat ion of excessive oil temperature is a

control valve lever that becomes hard to operate or sticks instead of returning to neutral.

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды