Broderson IC-200-2H Скачать руководство пользователя

Страница: 5 / 74

1-1

BRODERSON MANUFACTURING CORP.

IC-200-H INDUSTRIAL CRANE

INTRODUCTION

The Broderson IC-200-H was designed and built to provide safe, dependable and efficient crane

service. This we warrant by our testing and quality control procedures. To properly utilize the

full potential of the equipment, the following customer controlled conditions must exist:

The operator must understand the equipment.

The operator must know the operating characteristics.

The operator must observe the safety rules.

The equipment must be given proper maintenance.

This manual was written to provide information required for these conditions. T he

recommendations for periodic inspection, test and maintenance are minimum standards for safe

and economical performance.

When ordering parts: the unit serial number, unit model number, part number, part description

and quantity must be provided.

This unit must not be altered or modified without written factory approval.

To reorder this manual, ask for IC-200-H Operation and M aintenance Manual, Part Number-

990-30204. Contact your Broderson Service Representative at:

Broderson Manufacturing Corp.

P.O. Box 14770

Lenexa, Kansas 66285 USA

913-888-0606

NOTICE

If this crane becomes involved in an accident, please call Broderson Manufacturing Corp. at

913-888-0606, and ask for the Legal Department or the Service Manager. Also, please notify

your Broderson dealer.

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды