Broderson IC-200-2H Скачать руководство пользователя

Страница: 19 / 74

2-1

OPERATION SECTION

SAFETY RULES

GENERAL:

1. Since the manufacturer has no dir ect control over machine application and operation,

conformance with good safety practice is t he responsibility of the user and his oper ating

personnel.

2. 3.

4. The operator shall be r esponsible for those operations under his direct control. W henever

there is any doubt as to safety, the operator shall have the authority to stop and refuse to

handle loads until safety has been assured.

5. The operator shall not engage in any practice which will divert his at tention while actually

operating the crane.

6. Do not run the engine in an enclosed area or indoors without adequate ventilation.

7. Do not use ether for starting. Ether is hig hly flammable and can be ig nited by the intake

manifold heater grid, causing engine damage or operator injury.

8. This list of rules is only a supplem ent to all f ederal, state, and local saf ety rules that may

apply.

CRANE CONDITION:

1. Before beginning operation each day, thoroughly inspect the entire crane to be sure it is in

good operating condition.

2. Inspect load hoist rope and w edge socket daily. W e recommend rope inspection,

replacement and maintenance in accordance with ANSI B30.5, Sec. 5-2.4.

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды