Broderson IC-200-2H Скачать руководство пользователя

Страница: 12 / 74

1-8

Front Axle:

Standard:

Planetary drive/steer front axle with 15.78 to 1.0 ratio. Differential equipped with

"limited slip" feature. Driving effort is applied to wheel that has traction. Front axle

mounted rigidly to frame.

Calculated

Performance:

Gear

Drawbar Pull (pounds)

Travel Speeds (MPH)

1st

17,000*

2nd

8,900*

3rd

5,100*

4th

2,700*

*Calculated for GM 4.3L engine. W heels will spin in 1st or 2nd gear before these

values are reached with 2-wheel drive.

Rear Axle:

Standard

2-Wheel

Drive:

Steering axle with 1½ degree oscillation in either direction.

Optional

4-Wheel

Drive:

Planetary drive/steer axle with 24.98 to 1.0 ratio. Differential is not “limited slip” in

rear axle. 1½ degree oscillation in either direction. (Axle ratio compatible with 4WD

transmission output for front axle match.) Net Weight: 160 pounds (73 kg)

Steering:
Standard:

Hydraulic steering unit with two, 3-inch (7.6 cm) cylinders attached to each ax le.

Allows limited steering when engine is not running. Rear axle is the primary steer.

An electric switch in the operator’s compartment is used t o select rear-wheel

steering, four-wheel round steering or crab steering. Electronic sensors and control

box automatically align the steering when a new mode is selected.

Brakes:
Standard:

Split-system, four-wheel hydraulically-boosted multiple-plate wet disc brakes. Uses

mineral oil. Hand lever actuated disc-type parking brake on transmission.

Tires:

Standard 2-Wheel & 4-Wheel Drive:

15x22.5, 16-ply rating.

Tire

Options:

Non-Marking

Pnuematic:

385/65D22.5 16-ply rating Net Weight: 20 pounds (9 kg)

Foam Filling of Tires:

Foam filling of four IC-200 tires. Net Weight: 2000 pounds (907 kg)

Spare Tire and Wheel Mounted Standard Tire:

Extra wheel with standard tire (15X22.5, 16-ply) mounted, ready for service. Net

Weight: 350 pounds (159 kg)

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды