Broderson IC-200-2H Скачать руководство пользователя

Страница: 11 / 74

1-7

Optional Engines and Engine Accessories:

Diesel

Engine:

Cummins QSB3.3L Turbo, EPA Tier 4i:

Cummins QSB3.3 Tier 4 I nterim turbocharged diesel engine. Water cooled, 4-

cylinder, 199 CI D (3.3L), 3.74-inch (95 mm) bore, 4.53-inch (115 mm) stroke,

100 HP (75 kW) at governed speed of 2600 RPM. Maximum torque is 306 ft-lbs

(415 Nm) at 1600 RPM. 120-amp alternator included. 30-gallon (114 L) fuel tank

capacity. High temperature and low oil pr essure shutdown included in eng ine

management system. Throttle control switch for setting engine speed at 1200 or

1800 RPM. Diesel oxidation catalyst muffler; Air intake pre-cleaner; Charge air

cooler; 1500 watt, 120 vac, block heater; and grid heater included. Net Weight:

200 pounds (91 kg)

Spark

Arrester

Muffler:

Spark arrester muffler used in addition to standard muffler. Net Weight: 10

pounds (5 kg)

Engine Heater for Dual Fuel Engine Only:

Heater for engine. Engine coolant heater installed with hoses in coolant system

to circulate warm water through engine. Plug s into 120V AC ex tension cord.

1500 watts.

Transmission:
Standard

2-Wheel

Drive:

Powershift transmission with four speeds in f orward and reverse. Provides

powershifts at any engine speed in any gear. All shif ting is done w ith a sing le

lever electrical control mounted on t he steering column. Multiple-disc clutch

packs operated by solenoid valves provide reverse, neutral, forward and speed

selection. Equipped with oil cooler and filter.

Optional 4-Wheel Drive Transmission:

Same as 2WD transmission with an additional output shaft to drive the rear axle.

Electro-hydraulic control for shifting between 2WD and 4W D. T his option

includes the 4-wheel drive axle listed below.

Transmission

gear

ratios:

Forward and Reverse (2WD & 4WD)

1st

5.72 to 1.0

2nd

3.23 to 1.0

3rd

1.77 to 1.0

4th

1.00 to 1.0

Torque

Converter:

Standard:

Stall torque ratio of 2.2:1, attached to engine flywheel

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды