Broderson IC-200-2H Скачать руководство пользователя

Страница: 46 / 74

3-2

16. Use a hoist when lifting components that weigh 50 pounds (22 kg) or more. Follow all

hoist and rigging safety rules.

17. Do not use lower grade fasteners if replacements are necessary.

18. When reinstalling wiring or plumbing after repairs, be sure that it will not be damaged by

rubbing against sharp, rough or hot surfaces or edges.

19. Never use a rope clip on liv e side of the load hoist rope. This will seriously weaken the

rope. Death or serious injury can result from the misuse of a rope clip on the hoist rope.

20. Replace any instruction or warning placards that are lost or damaged or not readable.

21. Always replace all guards and covers after working on the crane.

22. After working on the hydraulic system, remove air from the lines and cylinders involved by

cycling them full stroke with the engine running until the functions operate smoothly.

23. When welding on the crane or on anything connected to the crane by wire rope or other

conducting link, disconnect the battery, the Rated Capacity Limiter display and computer

and the engine electronic control module. W hen welding on the boom or turntable as-

sembly, remove the cable reel and any other electronic components bolted to these as-

semblies.

24. When using pressure spray to clean the crane, cover all elect ronic components with

sheets of plastic to protect them from spray.

25. Do not allow antifreeze to contact skin. Rinse of f spills immediately with plenty of water.

Antifreeze is highly toxic if ingested.

26. Always disconnect negative cable f irst and r efasten last to prevent accidental short

through chassis components.

C A U T I O N

Even with low voltage electrical systems, severe arcing can occur. Electrical shock or
component damage can result from contact with energized conductors. Use caution
when working with any electrical device.

Courtesy of Crane.Market

Содержание IC-200-2H











































































Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды

Broderson IC-200-2H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IC-200-2H

Отзывы:

Похожие инструкции для IC-200-2H

Бренды по названию

Популярные бренды