User Guide
NetXtreme II
January 2010
Bro a d c o m Co rp o r a ti o n
Document
ENGSRVT52-CDUM100-R
iSCSI Boot
Page 79
•
Boot to iSCSI target
: Disabled
•
DHCP Vendor ID
: BRCM ISAN
•
Link Up Delay Time
: 0
•
Use TCP Timestamp
: Enabled
•
Target as First HDD
: Disabled
•
LUN Busy Retry Count
: 0
•
IP Version
: IPv6. (For IPv6, non-offload.)
•
Windows HBA Boot Mode
: Disabled
4.
Select
ESC
to return to the
Main
menu.
5.
From the
Main
menu, select
Initiator Parameters
.
6.
From the
Initiator Parameters
screen, type values for the following:
•
IP Address
•
Subnet Mask Prefix
•
Default Gateway
•
Primary DNS
•
Secondary DNS
•
iSCSI Name (corresponds to the iSCSI initiator name to be used by the client system)
NOTE:
Carefully enter the IP address. There is no error-checking performed against the IP address to check for
duplicates or incorrect segment/network assignment.
7.
Select
ESC
to return to the
Main
menu.
8.
From the
Main
menu, select
1st Target Parameters
.
9.
From the
1st Target Parameters
screen, enable
Connect
to connect to the iSCSI target. Type values for the following
using the values used when configuring the iSCSI target:
•
IP Address
•
TCP Port
•
Boot LUN
•
iSCSI Name
10.
Select
ESC
to return to the
Main
menu.
11.
A second iSCSI boot adapter can be configured for redundancy in the event the primary adapter fails to boot. To
configure the secondary device parameters, select
Secondary Device Parameters
from the
Main
menu (see
Parameters for a Secondary Adapter
). Otherwise, go to step 12.
12.
Select
ESC
and select
Exit and Save Configuration
.
13.
Select
F4
to save your MBA configuration.
14.
If necessary, return to the iSCSI Boot Configuration Utility to configure a second iSCSI target.
Dynamic iSCSI Boot Configuration
In a dynamic configuration, you only need to specify that the system’s IP address and target/initiator information are provided
by a DHCP server (see IPv4 and IPv6 configurations in
Configuring the DHCP Server to Support iSCSI Boot
). For IPv4, with
the exception of the initiator iSCSI name, any settings on the Initiator Parameters, 1st Target Parameters, or 2nd Target
Parameters screens are ignored and do not need to be cleared. For IPv6, with the exception of the CHAP ID and Secret,
any settings on the Initiator Parameters, 1st Target Parameters, or 2nd Target Parameters screens are ignored and do not
need to be cleared. For information on configuration options, see
Содержание BCM5706C
