2-31
=>
Safety precautions
2.2 RECOMMENDATIONS
>
Comply with the machine maintenance messages.
>
Protect the machine's power cords.
>
Contact a Briot technician for all repairs and always order Briot spare parts.
>
Use only products delivered and specified by Briot.
>
The machine is guaranteed to function correctly if the procedures stipulated in this manual are complied with.
>
Ensure that the edger is cleaned regularly.
Clean the outer cover with a clean, soft cloth moistened with a little alcohol.
CAUTION: Do not use the following products for cleaning:
Products containing ammonia, soda or acetic acid
Organic products such as acetone, benzene or trichlorethylene.
>
Touch screen:
Do not press too hard on the touch screen or you could break it.
Do not press the screen with sharp objects such as a pens, scissors, pliers, etc.
Make sure your fingers are dry when touching the screen.
If the reaction zone does not correspond to the key location, adjust the touch screen in relation to the display
(see paragraph Adjusting the touch screen , Chapter Settings & adjustments) .
Clean the touch screen with a soft, clean, dry cloth.
>
Scanform zone:
To ensure an optimum working life of the equipment and performance of the shapes and sizes:
→
Close the lugs of the frame eyewires.
→
Clean the frame in the ultrasonic bath before entering the data.
In the event of a data entry problem, push the emergency stop button and wait until the Scanform returns
control to you before resuming the operations.
>
Centering/locking system zone:
Do not scratch or put your fingers on the optical components of the blocking system (collimator lens, ground
glass screen) or you may permanently alter the measurements of the equipment.
Ensure the lens you have inserted is clean.
Before blocking the lens, always check which type of block is required and ensure that the lens blocking and
lens holder adaptors are appropriate for the job to be done.
Use blocks designed and supplied by Briot.
Use new adhesives.
Lay the lens down on the three lens holder pins, so that it is stable.
Dot single vision lenses at their optical center using a frontofocometer. Highlight the marking with a fine
felt-tip pen No. 24 06 211.
Deblocking a lens.
→
Even though the deblocking system is easy to use, follow the procedure described below to avoid the risk
of damaging the lens.
Change the blocks regularly. Their lifespan is 100 blocking operations
.
>
Edging zone:
Before starting the machine, check that the water supply is working (valve open).
Make sure that the installation is perfectly water-tight.
Change the water in the tank regularly if your machine operates in closed water circuit mode.
Make regular checks of the condition of the feeler tips and change them if they are worn, chipped or
damaged.
Remove glass and CR39 dust daily using clean water and a soft sponge or a brush so as not to scratch the
plastic surfaces.
Clean the visor regularly.
Содержание emotion
