Maintenance...
Messages
5-191
0x103
Corrupt OMA frame.
The OMA frame sent by the
server displays a fault which
princidents reception.
Contact a Briot technician.
0x104
Invalid OMA frame.
The OMA frame sent by the
server displays parameters
which the edger does not
recognize.
Contact a Briot technician.
0x300
Touch screen not detected.
When the edger is initialised, the
touch screen is not detected.
Contact a Briot technician.
0x404
Safety-Bevel or Grooving
impossible.
Safety-bevel and/or groove
cannot be made.
Confirm the message.
Select new parameters.
0x405
Holes deleted (at least one
was unfeasible).
Do you want to continue?
The drilling plan includes at least
one hole positioned too close to
the block or too far from the
edge of the lens.
YES: the lens is edged but not
drilled. Then you can produce
the holes with a drill.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x406
External safety-bevel will
not be made.
Do you want to continue?
External safety-bevel cannot be
made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
an external safety-bevel.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x407
Internal safety-bevel will not
be made.
Do you want to continue?
Internal safety-bevel cannot be
made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
an external safety-bevel.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x408
Groove will not be made.
Do you want to continue?
The groove cannot be made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without a
groove.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x409
Safety-bevels will not be
made.
Do you want to continue?
Safety-bevels cannot be made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
an external safety-bevel.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x40A
External safety-bevel &
groove will not be made.
Do you want to continue?
External safety-bevel and
groove cannot be made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
an external safety-bevel or a
groove.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x40B
Internal safety-bevel &
groove will not be made.
Do you want to continue?
Internal safety-bevel and
groove cannot be made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
an internal safety-bevel or a
groove.
NO: the lens is not edged.
Remove the lens from the
edging station.
#
Message
Condition(s) for
display
Action(s)
Содержание emotion
