Maintenance...
Messages
5-192
0x40C
Safety-bevels and groove
will not be made.
Do you want to continue?
Safety-bevels and groove
cannot be made.
The lens is too thin and/or the
shape is too small.
YES: the lens is edged without
the safety-bevels or the groove.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x40D
Lens too thick: edging
impossible.
The lens thickness at the
measured point is greater than
11 mm. The lens cannot be
edged.
Confirm the message.
Remove the lens from the
edging station.
0x40E
Edging stopped: visor open.
You have opened the visor
during the edging cycle.
Check the lens and remove it
from the edging station.
Confirm the message.
0x40F
Problem detected. Machine
re-initialisation.
A problem has been detected
during the cycle. The machine
must restart before continuing.
Confirm the message.
0x410
Lens too small. Do you want
to continue?
Lens too small or too off-
centered in comparison with the
shape.
YES: the lens is felt again 0.5
mm closer to the interior.
It can be re-felt 3 successive
times, 0.5 mm closer to the
interior each time.
NO: Remove the lens from the
edging station.
0x411
Small adaptors fitted?
The 19 mm diameter adaptors
are required for the procedure
you have selected.
Confirm the message.
Fit the small adaptors.
0x412
Small
adaptors
fitted?
The 17 mm diameter flat
adaptors are required for the
procedure you have selected.
Confirm the message.
Fit the small flat adaptors.
0x413
Edging impossible: radius
too small.
The shape is smaller than the
smallest adaptor.
Confirm the message.
Remove the lens from the
edging station.
0x414
A feeler fault has been
detected during feeling.
An irregularity has been
detected during lens feeling.
Confirm the message.
Restart the cycle and observe
the lens feeling process:
- If one of the tips is unclipped,
refit it.
- If not, proceed with the lens
feeling adjustment.
0x415
Bevel out of lens.
The bevel is outside the lens in
at least one point.
Confirm the message.
Visualise the fault on the control
screen and proceed as required.
0x416
Retouch impossible.
You have activated the retouch
control and the lens detected
does not match the parameters
of the lens you wish to retouch.
Confirm the message.
Remove the lens fitted on the
shafts.
Fit the lens you wish to retouch.
0x41A
Lens too thin for grooving.
Do you want to continue?
A thickness of less than 1 mm
has been detected in at least
one point of the lens.
YES: The lens is edged with
rimless finishing.
NO: The cycle is stopped.
Remove the lens from the
edging station.
#
Message
Condition(s) for
display
Action(s)
Содержание emotion
