Maintenance...
Messages
5-185
5.12MESSAGES
5.12.1T
YPES
OF
MESSAGES
There are three types of messages:
>
Information messages
>
Warning messages
>
Fault messages
5.12.2L
IST
OF
MESSAGES
.
The table below shows all the messages, the conditions for their display and the action to undertake.
#
Message
Condition(s) for
display
Action(s)
0x0
Grooving & drilling not
allowed on mineral lens.
Mineral lens material can neither
be grooved or drilled.
Adapt your job to Mineral lens
material: bevel or rimless
finishing
or
Use another lens material for
the current job.
0x1
Edging parameters
incomplete.
You have started edging before
selecting all the parameters.
Check that all parameters have
been selected.
No "To be defined" button must
be visible!
0x2
Please select a job.
You have started edging without
first loading a shape.
Load a shape, select the
parameters then start the
edging process.
0x4
Edging in progress.
Job A is in progress and you
have called up job B.
Wait until the end of the job in
progress before loading another
job.
0x5
Unknown job number.
The job you are trying to load
does not exist on the server.
Check the job number and load
another number.
0x7
Do you want to re-edge the
same lens ?
You have just edged a lens and
then re-started a cycle on the
same job number and the same
side.
YES: If you wish to edge the
same lens again or if you wish to
edge several lenses with the
same parameters.
NO: Fit a new lens and proceed
as you wish.
0x8
Please wait
during machine shut down.
You have pressed for more than
6 seconds on the machine
standby button.
Wait until the machine has
stopped before switching off.
0x9
You can safely turn off your
machine.
You have asked for the machine
to stop. The close-down
procedure has been followed.
The machine can now be
switched off.
Switch off the machine (On/Off
button pressed-in and unlit).
0xA
Incompatible edger
configuration.
Trivex lens not allowed.
The job you have loaded calls
for Trivex® lens material.
In the personalisation menus,
you have excluded this
parameter.
Therefore the edger cannot
accept this job.
Confirm the message.
If you wish to load this job
nonetheless, change the
personalisation of the pull-down
menus.
Select Trivex® lens material.
Load the job again.
Содержание emotion
