Maintenance...
Messages
5-193
0x41B
Lens too small.
Feeling carried out 3 successive
times, 0.5 mm closer to the
interior each time.
Lens too small or too off-
centered in comparison with the
shape.
Confirm the message.
Remove the lens from the
edging station.
0x41C
Mill bit diameter > hole
diameter.
Do you want to drill?
The diameter of at least one
hole is smaller than the diameter
of the mill bit.
But the minimum drilling
diameter is equal to the bit
diameter.
YES: The hole(s) will be drilled
with a minimum diameter equal
to that of the bit.
NO: the lens is not edged.
Remove the lens from the
edging station.
0x506
Please remove lens to free
mill bit before
acknowledging this
message.
A fault has occurred when the
mill bit was not in its housing.
The lens could be damaged.
Make sure that the machine is
switched off.
Free the lens from the mill bit
carefully.
Restart the machine.
0x508
Replacing the mill bit is
recommended.
Do you want to do it now?
At start-up, the machine records
total drilling time greater than
1hr. Replacing the mill bit is
recommended.
YES: Change the mill bit (see
“Replacing the mill bit”,
page 129)
NO: You accept the risk of using
a worn mill bit. The risk of
chipping the lens is increased.
The message is displayed at
each machine start-up.
0x509
Mineral wheel dressing
recommended.
Do you want to do it now?
1000 mineral lenses have been
edged. Dressing the mineral
roughing wheel is
recommended.
YES: Dress the mineral roughing
wheel. (see “Dressing a wheel”,
page 137)
NO: You accept the risk of using
a loaded wheel. The risk of lens
size error is increased, and so is
the edging time. The message
is displayed at each machine
startup.
0x50A
Finishing wheel dressing
recommended. Do you want
to do it now?
800 mineral lenses have been
edged with bevel finishing.
Finishing wheel dressing is
recommended.
YES: Dress the finishing wheel
(see “Dressing a wheel”,
page 137)
NO: You accept the risk of using
a loaded wheel. The risk of lens
size error is increased, and so is
the edging time. The message
is displayed at each machine
startup.
0x902
Dressing impossible
Wrong disc thickness.
The thickness of the fitted disc
does not match the theoretically
required thickness.
Confirm the message.
Use an appropriate dressing
disc.
0x903
Dressing impossible
Disc diameter too small.
The volume of material to be
machined is less than the
minimal volume required.
Confirm the message.
Use an appropriate dressing
disc.
0x50C
Weak electrical supply.
The voltage detected is less than
20 % of the normal voltage.
Please contact your electricity
supplier.
#
Message
Condition(s) for
display
Action(s)
Содержание emotion
