Maintenance...
Adjustments
5-153
#10 When the icon
is displayed, get the tool No. 14 04 185.
#11 Ensure that the diameter value of the round shape marked on the tool is the same
as the value displayed on the screen.
If the values are the same, go to the next step.
If the values are not the same, enter the values marked on the tool using the
following key:
Note: The value should be around 40 mm.
#12 Position the tool in the frame-holder (Figure 2).
#13 Press
.
Result: The sylus is inserted in the tool and adjustment is started.
#14 When the adjustment is finished, check the measured valued which are displayed
on the screen.
Adjustment is correct when all the dots in front of the parameters are green.
Note: If one or more dots are red, repeat the step by pressing the
key. If the problem cannot be solved, please contact your distributor.
#15 Remove the tool.
#16 Press
.
Result: The
e
motion validates this adjustment and proceeds to the next one.
#17 When the icon
is displayed, insert the round pattern
No. 14 04 192 on the pattern holder.
#18 Ensure that the diameter value of the pattern marked on the tool No. 14 04 192
is the same as the value displayed on the screen.
If the values are the same, go to the next step.
If the values are not the same, enter the values marked on the tool using the
following key:
Note: The value should be around 40 mm.
Содержание emotion
