BOXER 700HDX Скачать руководство пользователя

Страница: 90 / 92

General Specifications

6.3

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

OF A COMPACT UTILITY LOADER WITH AN ATTACHMENT.

DO NOT REMOVE THIS PAGE FROM THE MANUAL.

15 DEGREES MAX.

1. Fold this page along dotted line indicated above. DO NOT remove the page

from the manual.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of the hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

THIS

IS A

15 DE

GREE

SLOP

DO NOT TRAVEL ACROSS OR UP AND DOWN

A SLOPE GREATER THAN 15 DEGREES

To avoid serious injury, operate your unit up and down

the face of slopes.

Travel across slopes with great caution.

Do not operate on slopes greater than 15 degrees.

Make turns gradually to prevent tipping or loss of control.

Exercise extreme caution when changing direction on

slopes.

Control of the machine may be affected by installed

attachments.

Reduce travel speed on slopes.

Read and understand all Warnings and Operating

Instructions in the Operator’s Manual.

WARNING

FOLD

ALONG

DOTTED

LINE

DO NOT TRAVEL ACROSS OR UP AND DOWN

A SLOPE GREATER THAN 15 DEGREES.

THIS

IS A

15 DEGREE

SLOPE

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды