BOXER 700HDX Скачать руководство пользователя страница 85

Страница: 85 / 92

Troubleshooting

5.2

Problem

Possible Causes

Corrective Action

Engine will not start, starts

hard, or fails to keep run-

ning.

• Auxiliary hydraulics lever is

not in neutral position with

a hydraulically powered

attachment installed.

• Move lever to neutral

position.

• Fuel tanks are empty.

• Fill fuel tanks with diesel fuel.

• Glow plugs not working.

• Cycle glow plugs for about

10 seconds and try starting

engine.

• Air cleaner is dirty.

•

Clean air filter housing and

replace the filter elements.

• Injectors may be plugged

• Have the diesel fuel injectors

serviced by your Authorized

Service Dealer.

• Air in fuel system.

• Bleed air from fuel system.

See Kubota engine manual

for complete procedures and

see Section 4, Replacing

Fuel Filter for air bleed

instructions.

•

Dirty or contaminated fuel filter.

•

Replace fuel filter.

• Dirt, water or stale fuel is in

fuel system.

• Drain fuel in tanks into

an appropriate storage

container and dispose of bad

fuel properly.

•

Refill fuel tanks with fresh,

clean fuel.

•

Replace fuel filter.

• 30 Amp fuse blown.

• Replace fuse.

Engine loses power.

• Engine load is excessive.

• Reduce ground speed.

• Reduce speed of

attachment.

• Air cleaner is dirty.

•

Clean air filter housing and

replace the filter elements.

• Engine oil level in crankcase

is low.

• Add the appropriate engine

oil to crankcase. See engine

manual for oil specifications.

•

Cooling fins and air passages

under engine blower housing

are plugged.

• Remove obstruction

from cooling fins and air

passages.

• Fuel injectors may be plugged

or dirty.

• Have the diesel fuel injectors

serviced by your Authorized

Service Dealer.

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды