manualshive.com logo in svg

BOXER 700HDX, Руководство оператора

Поделиться
Скачать
BOXER 700HDX Скачать руководство пользователя страница 9

IX

Table of Contents 

Boxer Product Warranty ..................................................................................iv
Safety Introduction ..........................................................................................vii

Be Prepared - Get to Know All Operating and Safety Instructions ...... vii

Learn the Signal Words Used with the Safety Alert Symbol ................ vii

Section 1 – Safety Precautions ....................................................................1–1

General Safety ..........................................................................................1–1

Operating Safety .......................................................................................1–2

Service & Maintenance Safety..................................................................1–4

Electrical System Hazards ........................................................................1–4

Battery Hazards .................................................................................1–5

Jump Starting/Battery Charging Hazards ..........................................1–5

Hydraulic System Hazards .......................................................................1–6

Fueling Hazards........................................................................................1–7

Section 2 – Operating Controls ....................................................................2–1

Component Locations ...............................................................................2–1

Left Front View ...................................................................................2–1

Right Rear View .................................................................................2–2

Safety Decals .....................................................................................2–3

Operating Controls .............................................................................2–5

Operating Controls Description ..........................................................2–6

Section 3 – Pre-Start Inspection and Operation .........................................3–1

Pre-Start Inspection ..................................................................................3–1

Daily Service Checks ................................................................................3–1

Cylinder Lock Installation ..........................................................................3–9

Cylinder Lock Removal ......................................................................3–9

Operating Instructions.............................................................................3–10

Machine Start-up .............................................................................3–10

Machine Shut-down ......................................................................... 3–11

Transportation ..................................................................................3–12

Lifting Procedures ............................................................................3–13

Machine Travel Controls .........................................................................3–14

Attachment Installation and Removal .....................................................3–18

Attachment Lock Pins ......................................................................3–18

Installation of Non-Hydraulically Powered Attachments ..................3–19

Removal of Attachment ....................................................................3–21

Installation of Hydraulically Powered Attachments ..........................3–21

Operating Instructions for a Hydraulic Attachment ..........................3–26

Removal of Hydraulically Powered Attachments .............................3–29

Содержание 700HDX





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды