BOXER 700HDX Скачать руководство пользователя страница 70

Страница: 70 / 92

Routine Service and Maintenance

4.17

i. Reinstall the end cap so the dust ejector valve is down and secure the end cap with the

two retaining clips.

*In extremely dusty or dirty operating conditions, this service cycle may need to be

shortened.

Replace fuel filter.

Make sure to clean up any spilled fuel from in and around the engine compartment of

the machine. Spilled fuel may be ignited by a hot engine.

Locate fuel filter assembly through the opening in the frame along the left side of the

machine.

Unscrew the filter canister.

NOTE:

•

The fuel filter will be filled with diesel fuel. Make sure to drain the fuel from the filter

into an appropriate container.

•

Dispose of the used fuel filter in an appropriate manner, and according to State and

Local regulations.

Before installing the new canister filter, lubricate the rubber sealing ring on top of the

filter with a small amount of diesel fuel.

Install the new filter.

Figure 4-18 Fuel Filter Assembly

NOTE:

Place a container underneath the fuel injection pump to catch any spilled

diesel fuel. Dispose of the used fuel in an appropriate manner.

CAUTION

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды