BOXER 700HDX Скачать руководство пользователя

Страница: 29 / 92

Pre Start Inspection and Operation

3.3

3. The Boxer has two saddle fuel tanks (Item 1,

Figure 3–3

). Remove cap (Item 2,

Figure 3-3

) and visually inspect fuel level. Make sure that each tank has been

filled on a daily basis.

Figure 3-3 Fuel Level Check

•

Carefully pour the fuel into the tank, until fuel level is at bottom of fill spout.

•

Allow engine to cool before filling fuel tanks.

•

Do not overfill, fuel could spill onto hot engine parts and ignite or explode.

4. Check engine coolant level.

The coolant is hot and under pressure. DO NOT check until the engine radiator is cool

to the touch.

• Remove radiator cap (Item 1,

Figure 3–4

) and check the radiator fluid level. The proper

coolant level will be to the bottom of filler neck.

CAUTION

NOTICE

CAUTION

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды