BOXER 700HDX Скачать руководство пользователя

Страница: 56 / 92

Routine Service and Maintenance

4.3

3. Check engine oil -

a. Make sure that the engine is OFF.
b. Pull out the dipstick (Item 1,

Figure 4–2

) and look for the “FULL” line.

Figure 4-2 Oil Level Check

c. If the engine oil level is below the add line, indicated by the letter “A” on the dipstick,

carefully add the proper amount of oil through the engine oil filler (Item 1,

Figure

4–3

). The correct SAE viscosity grade of oil is determined by the minimum ambient

temperature during cold engine start-up, and the maximum ambient temperature during

operation. The engine is filled at the factory with Chevron Delo 400 Multigrade SAE

15W-40. The recommended ambient temperature range for this oil is 14° F (-10° C)

minimum to 122° F (50° C) maximum. Refer to the engine Operation and Maintenance

Manual for additional information on the proper selection of engine oil.

NOTE:

Make sure to reinstall and secure the oil filler cap.

Figure 4-3 Engine Oil Fill

NOTE:

Extremely dusty or dirty working conditions may require more frequent

checking, filling and/or changing of engine oil.

After filling the oil, wait a few minutes and check the oil level again.

e. Make sure to securely reinstall the dipstick into the dipstick tube before starting the

engine.

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды