BOXER 700HDX Скачать руководство пользователя

Страница: 71 / 92

Routine Service and Maintenance

4.18

e. Loosen, but DO NOT remove, the air bleed bolt (Item 2,

Figure 4–19

f. Raise and lower the primer pump handle (Item 1,

Figure 4–19

) until only diesel fuel

without any air bubbles comes out of the air bleed.

g. Fully tighten the air bleed bolt.

Figure 4-19 Fuel Feed Pump Lever

6. Check battery for signs of leakage and for corrosion on the battery cables.

• On a monthly basis, check the battery for signs of leaking electrolyte. If any signs of

damage are visible, remove and replace the battery.

Wear the proper protective clothing when handling the battery. Leaking battery fluid

contains acid that can cause burns. Fumes from the leaking fluid can cause respiratory

problems.

• To prevent corrosion, spray on a battery protectent and sealer onto both terminals and

cable clamps after cables are installed.

• The electrical system on this machine is a NEGATIVE ground system.

• Check both of the battery cables for signs of damage or corrosion. Loosen the cable

clamps and remove the cable from the battery. Clean the terminals with a battery brush.

Reinstall and secure the cable clamps.

CAUTION

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Похожие инструкции для 700HDX

Бренды по названию

Популярные бренды