BOXER 700HDX Скачать руководство пользователя страница 16

Страница: 16 / 92

Safety Precautions

1.6

Hydraulic System Hazards

The hydraulic system is under pressure whenever the engine is running and may hold

pressure even after the engine is shut off. Cycle all hydraulic controls after the loader boom

is resting on the ground. Some components will retain residual or trapped pressure. Use

extreme caution when removing any hydraulic component.
During inspection of the hydraulic system:

• Cycle all hydraulic controls to release residual pressure.
• Wait for the hydraulic fluid to cool down before disconnecting any hydraulic lines. Hot

hydraulic fluid can cause severe burns.

Hydraulic oil under pressure can penetrate body tissue causing serious injury and

possible death. When troubleshooting a hydraulic system for leaks, always use

cardboard or wood as a detector. DO NOT USE YOUR BARE HANDS. If you are

injected with hydraulic oil or any other fluids, immediately seek treatment by a doctor

trained in the treatment of penetrating fluid injuries.

• Hydraulic system, loosen the filler cap slowly to allow any pressure in the hydraulic tank

to be reduced. Hydraulic fluid can cause permanent eye injury. Wear safety glasses or a full

face shield to provide appropriate eye protection.

• When venting or filling the hydraulic tank, loosen the filler cap slowly to allow any

pressure in the hydraulic tank to be released and remove the cap gradually.

WARNING

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды