BOXER 700HDX Скачать руководство пользователя страница 86

Страница: 86 / 92

Troubleshooting

5.3

Problem

Possible Causes

Corrective Action

Engine loses power.

•

Dirty or contaminated fuel filter.

•

Replace fuel filter.

• Dirt, water, or stale fuel is in

fuel system.

• Drain fuel in tanks into

an appropriate storage

container and dispose of bad

fuel properly.

•

Refill fuel tanks with fresh,

clean fuel.

•

Replace fuel filter.

Engine overheats.

• Engine load is excessive.

• Reduce ground speed.

• Reduce speed of

attachment.

• Engine oil level in crankcase

is low.

• Add the appropriate engine

oil to crankcase. See engine

manual for oil specifications.

•

Cooling fins and air passages

under engine blower housing

are plugged.

• Remove obstruction

from cooling fins and air

passages.

• Cooling system low on coolant •

Check and refill coolant to

levels and with the type

of coolant indicated in the

engine manual.

• Dirty or plugged radiator

• Clean the radiator.

Abnormal engine vibration.

• Engine mounting bolts are

loose.

• Tighten engine mounting

bolts.

With the machines engine

turned off, the boom creeps

downward more than 3” per

hour (less than 3” per hour

is normal for this machine).*

• Valve spool leakage.

• Contact Service Dealer.

• Cylinder seals are leaking.

• Replace cylinder seals.

With the machines engine

turned off, boom drops

downward quickly and then

stops.

• Cylinder seals are leaking.

• Replace cylinder seals.

The machine does not

travel in either forward or

reverse directions.

• Engine is not running at full

speed.

• Advance throttle to full

engine speed.

•

Hydraulic fluid is cold.

•

Fully warm hydraulic fluid.

•

Hydraulic fluid level is low.

•

Check and fill the hydraulic

fluid tank with the

appropriate hydraulic fluid.

• Fuel tanks are empty and

engine stops.

• Fill fuel tanks with fuel.

• If all above has been checked. • Contact authorized service

dealer.

*Tested with warm oil and no more than 530 lbs (240 Kg) in the bucket. Measure the

downward drop at the attachment lock pins on the back of the mount plate.

Содержание 700HDX





























































































Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды

BOXER 700HDX, Руководство оператора

Результаты поиска

Содержание 700HDX

Отзывы:

Бренды по названию

Популярные бренды