Bovie Aaron 1250 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 68

Bovie Aaron 1250 Скачать руководство пользователя страница 47

INSTALLATION AND PLACEMENT

Place the Aaron 1250 Electrosurgical Generator on any flat surface with a tilt angle of not more than 10 degrees.
The unit relies on natural convection cooling. Do not block the rear vents.

Ensure that air flows freely on all sides of the unit.

WARNING

Connect the power cord to a properly polarized and grounded power source with the frequency
and voltage characteristics that match those listed on the back of the unit.

FUNCTIONAL (OPERATIONAL) CHECKS

Upon initial installation of the unit, perform the following checks. Refer to the figures in Controls and Indicators for
the location of connectors and generator controls.

WARNING

At no time should you touch the active electrode or bipolar forceps. A serious burn could result.

How to Set Up and Start the Aaron 1250 Unit

1. Verify that the Power Switch is in the OFF position and that no accessories are connected to the unit.

2. Connect a hospital-grade power cable to the AC power cable receptacle on the back of the unit, then to a
properly grounded wall outlet.

3. Connect a two-pedal footswitch to the matching footswitch receptacle on the back of the unit. Use only Aaron

footswitches. Although other types of footswitches may fit, they may not be compatible with this Electrosurgical
Generator.

4. Do not connect a Patient Return Electrode to the front of the unit at this time.

5. Turn the unit on by switching the power switch to the (ON) position.

6. The correct startup for the unit is a quick flash of all indicators and a series of beeps. The unit will return to the

last mode and power setting used.

How to Check the Patient Return Electrode Alarm Function

1. Adjust the power settings for each mode (Cut, Blend, Coagulation, Fulguration, and Bipolar) to one watt.

2. Press the Cut Pedal of the footswitch.

3. Verify that an alarm sounds for three seconds, and then the Patient Return Electrode Sensing Alarm Indicator

Light illuminates. This indicates NO patient return electrode connected to the unit.

4. Verify that adjusting the volume control on the back of the unit (while the alarm is sounding) cannot change the

alarm’s sound level.

47

Ser vice Guide • Aaron 1250

«
...
45
46
47
48
49
...
»

Содержание Aaron 1250





































































Отзывы:

Нет отзывов