Bovie Aaron 1250 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 68

Bovie Aaron 1250 Скачать руководство пользователя страница 11

UNIT DESCRIPTION

The Aaron 1250 electrosurgical generator is a self-contained unit, consisting of the main enclosure and power cord.
The main components incorporated in the generator include:

•

FRONT PANEL COMPONENTS

Power switch; two dials for controlling power output; membrane switches for

selecting modes; receptacles for connecting electrosurgical accessories; and indicators that show the current settings
and patient return electrode status.

•

REAR PANEL COMPONENTS

Volume control; footswitch receptacle; power cable receptacle and fuse holder;

equipotential grounding lug; and remote accessory receptacle.

•

INTERNAL COMPONENTS

Display board; main board; pad sensing module; speaker board; and relay board.

SAFETY PRECAUTIONS WHEN REPAIRING THE GENERATOR

Before servicing the Aaron 1250 Generator it is important that you read, understand, and follow the instructions
supplied with it. Also, be familiar with any other equipment used to install, test, adjust, or repair this generator.

General Warnings, Cautions, and Notices

WARNINGS

Use the generator only if the self-test has been completed as described. Otherwise, inaccurate
power outputs may result.

The instrument receptacles on this generator are designed to accept only one instrument at a
time. Do not attempt to connect more than one instrument at a time into a given receptacle.
Doing so will cause simultaneous activation of the instruments.

CAUTIONS

Do not stack equipment on top of the generator or place the generator on top of electrical
equipment. These configurations are unstable and / or do not allow adequate cooling.

Provide as much distance as possible between the electrosurgical generator and other electronic
equipment (such as monitors). An activated electrosurgical generator may cause electrical
interference with them.

Do not turn the activation tone down to an inaudible level. The activation tone alerts the surgical
team when an accessory is active.

NOTICES

If required by local codes, connect the generator to the hospital equalization (grounding) connector
with an equipotential cable.

Connect the power cord to a wall receptacle having the correct voltage. Otherwise, product dam-
age may result.

Active Accessories

WARNINGS

Shock Hazard

– Do not connect wet accessories to the generator.

Shock Hazard

– Ensure that all accessories and adapters are correctly connected and that no

metal is exposed.

11

Ser vice Guide • Aaron 1250

«
...
9
10
11
12
13
...
»

Содержание Aaron 1250





































































Отзывы:

Нет отзывов