Bostitch MB2140-E, Оригинальное руководство пользователя

Страница: 6 / 36

POWER ADJUSTMENT (TU-216-2330-E / TU-216-1825-E)
For maximum power: rotate valve anticlockwise as far as possible. (Fig. 6)
To reduce power: rotate valve clockwise for up to 30% reduction. (Fig. 7)
TOOL OPERATION CHECK (TU-216-2330-E / TU-216-1825-E):
WARNING! Remove all fasteners from tool before performing tool operation check.
A. With finger off the trigger, hold the tool with a firm grip on the handle.
B. Place the nose of the tool against the work surface.
C. Raise the secondary trigger device.
D. Pull the trigger to cycle the tool. Release the trigger and cycle is complete.
WARNING! With the secondary trigger device raised, the tool will cycle each time the trigger is pulled!
ADDITIONAL WARNINGS:
WARNING (TU-216-2330-E / TU-216-1825-E)! The secondary trigger device should be checked periodically, to
ensure it is operating correctly.
While following the above tool operation check notes, release the secondary safety trigger and the operating trigger
simultaneously, this should automatically lockout the operating trigger, preventing the tool from being actuated.
The tool should only then operate again when the secondary trigger device is raised and the operating trigger is
depressed.
WARNING! If the tool fails to work correctly contact you local STANLEY service centre or distributor for advice
before continuing to use it.
WARNING (TU-216-2330-E / TU-216-1825-E)! Under no circumstances should the secondary trigger device or the
operating trigger be by-passed, modified or removed.
FASTENER JAM CLEARING:
WARNING! Always disconnect air supply before clearing a jammed fastener.
TO CLEAR A JAMMED FASTENER:
1. Release the magazine and pull it back to stop pin feeding.
2. Loosen the two screws as shown in (Fig. 8) by one full turn.
3. Slide cover down until the two large clearance holes line up with the two screw heads as shown in (Fig. 9).
4. Pull the cover away from nose as shown in (Fig. 10).
5. Remove the jammed fastener.
6. Re-install cover, slide it up, tighten the two screws and close magazine.
7. Reconnect air hose.
UTILITY HOOK (MB2140-E- Fig 11)
These tools include an additional utility hook suitable for storage and temporary hanging of the tool.
WARNING! Never use the utility hook to hang the tool from the body, clothing or belt.
TECHNICAL DATA:
Please look for the technical data in the table marked ? at the end of this manual.
A Length mm. K Air consumption per shot @ 5.6 Bar
B Height mm. L Activation type
C Width mm. M Summer lubricant
D Weight Kg. N Winter lubricant
E Noise L
PA
, 1s, d O O-ring lubricant
F Noise L
WA
, 1s, d P Fastener Name
G Noise L
PA
, 1s, 1m Q Dimensions mm.
H Vibration m/s 2 R Head/crown
I P max Bar S Magazine capacity
J P min Bar T New Driver Length mm.
U Max. Depth Inside Piston mm.
FT70937-b-0610_Pinners_Manual:WS51301 TU-216-2330 Manual 12/1/11 12:47 PM Page 6
© Stanley Bostitch
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR
Α
π
αγορεύεται η ανα
π
αραγωγή χωρίς
π
ροηγού
μ
ενη άδεια
.
Τα
μ
η εξουσιοδοτη
μ
ένα αντίγραφα του
π
αρόντος
εγγράφου δεν α
π
οτελούν συ
μμ
όρφωση
CE
για τα
π
ροϊόντα
.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.