background image

                    Available from A1 Security Cameras 

    www.a1securitycameras.com email: [email protected]

AutoDome Pendant Arm Mount 

 Cable and Wire Standards | en 

27 

3.5.1 

Connecting to an LTC 4629 Head End Data/Video Transceiver 

1.   Connect the RS232 cable (TxD from the controller) to the RS232 RxD port (pin 1) of the 

LTC 4629. 

2.   Connect the ground wire of the controller to Pin 2 on the LTC 4629. 

3.5.2 

Configuring the VG5 AutoDome 

1.   Disconnect the power to the VG4 power supply unit; then open the unit. 

2.   Remove the green Serial Communications wire from the P106 connector. 

3.   Remove the 100 Ω resistor across the C+ and C- pins. 

4.   Cut the five wires from the green Serial Communications wire mating connector. 

Ensure that the insulation covers each wire to avoid wires from touching. 

5.   Cut back the insulation on the blue (ground) wire and on the green (RxD) wire enough to 

be able to connect these wires back into the P106 connector. 

6.   Connect the blue (ground) wire to the C- pin on the P106 connector. 

7.   Connect the green (RxD) wire to the C+ pin on the P106 connector. 

XF1

01

   24 VAC 

P10

7

HTR                  DOME

5 4 

3

2

P101 

(LED) 

X

F1

02 

24V     NC     24V 

P106 

P105 

GND TXD  RXD 

C+  C-

GND 

T

XD 

R

XD 

 

C+  C-

Figure  3.8 

Detail of P106 Connections 

Green RxD wire connected to C+ 

Blue Ground wire connected to C­

8.   Connect the fiber optic cable from the AutoDome to the LTC 4629. 

J

J

J103

J1 

9. 

Close the door to the power supply unit. 

Bosch Security Systems, Inc.  

Installation Guide 

F.01U.250.238 | 1.0 | 2011.08 

Содержание VGA-PEND-ARM





































Отзывы: