Bosch VGA-PEND-ARM Скачать руководство пользователя страница 9

Страница: 9 / 36

2.1.2

2.1.3

AutoDome Pendant Arm Mount

Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en

Installing the Pendant Arm Wall, Corner, and Mast
(Pole) Mounts

2.1

Unpacking

This equipment should be unpacked and handled with care. If an item appears to have been

damaged in shipment, notify the shipper immediately.

Verify that all the parts listed in the Parts List below are included. If any items are missing,

notify your Bosch Security Systems Sales or Customer Service Representative.

The original packing carton is the safest container in which to transport the unit and must be

used if returning the unit for service. Save it for possible future use.

2.1.1

Parts List

The following table lists the parts included with this mounting package.

Part Numbers

Mounting Plate

VGA-PEND-WPLATE

Optional Mounting Accessories

The following table lists the optional parts you may need for attaching a Pendant Arm to a

Wall, Corner, or Mast.

Mounting Options

Part Numbers

Pendant Arm with wiring (no power supply)

VGA-PEND-ARM

Pendant Arm with wiring (no power supply) for a Pressurized

Environmental Housing

VGA-PRES-ARM

Corner Mount Plate

VG4-A-9542

Mast Mount Plate

VG4-A-9541

Optional Power Supplies

The VGA-PEND-WPLATE does not come with an attached power supply. The following table

lists the optional power supplies that are compatible with VG5 Series AutoDomes:

Mounting Options

Part Numbers

24 VAC (no transformer), NEMA-rated with cover

VG4-A-PSU0

120 VAC transformer, NEMA-rated with cover

VG4-A-PSU1

230 VAC transformer, NEMA-rated with cover

VG4-A-PSU2

Bosch Security Systems, Inc.

Installation Guide

F.01U.250.238 | 1.0 | 2011.08

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Содержание VGA-PEND-ARM





































Результаты поиска

Содержание VGA-PEND-ARM

Отзывы:

Бренды по названию

Популярные бренды

Bosch VGA-PEND-ARM, Руководство по установке

Результаты поиска

Содержание VGA-PEND-ARM

Отзывы:

Бренды по названию

Популярные бренды