16
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts
AutoDome Pendant Arm Mount
9.
Analog AutoDome
: Attach a BNC connector to the incoming video coax cable. If using
UTP for video attach an RJ45 plug to the incoming UTP cable. If installing a Fiber Optic
model, attach an ST fiber plug to the optic fiber cable. Refer to
Section 3 Cable and Wire
Standards, page 19
, for the different methods of transmitting video and control protocols,
and wire specifications.
Note:
Do not connect the RJ45 connector unless using UTP video.
10.
AutoDome 600 Series
: If using a coax cable, connect the incoming coax cable to the BNC
jack (female connector enclosed by the plastic cover) on the coax cable with ferrite.
Slide the plastic cover over the connection. Refer to
Section 2.4.1 Coaxial Cable
Connections, page 12
.
11.
AutoDome 600 Series
: Connect the BNC plug (male connector) of the coax cable with
ferrite to the BNC jack connector from the Pendant Connector Harness and slide its
plastic cover over the connection.
Section 2.4.1 Coaxial Cable Connections, page 12
.
12.
Analog AutoDome:
Connect the incoming video coax cable to the BNC connector (cable
4) and slide its plastic cover over the connector.
13.
Analog AutoDome
: If using UTP for video, connect the incoming RJ45 video connector,
installed previously, to the UTP Video/Ethernet cable (cable 5). Refer to
Section 3 Cable
and Wire Standards, page 19
, for detailed wire and connection information.
14.
IP AutoDome
: Connect the incoming RJ45 video connector, installed previously, to the
UTP Video/Ethernet cable (cable 5). Refer to
Section 3 Cable and Wire Standards, page 19
,
for detailed wire and connection information.
15. Connect the outgoing alarm wires to the flying leads coming from the 4-pin Alarm
Outputs cable (cable 6).
16. Connect the incoming alarms wires to the flying leads coming from the 6-pin Alarm Inputs
cable (cable 7).
17.
Analog AutoDome
: Connect the incoming serial communication wires to the 6-pin mating
connector supplied with the VGA-PEND-WPLATE kit. Ensure that the 100 Ω resistor
remains connected to the Biphase C- and the Biphase C+ terminals. Remove the resistor
only in the following cases:
–
If the AutoDome is not the last AutoDome in a daisy chain.
–
If the Biphase C- and the Biphase C+ terminals receive a line input audio signal.
Refer to
Section 3 Cable and Wire Standards, page 19
, for detailed wire and connection
information.
18. Attach the 6-pin serial communication mating connector to the Serial Communication
(cable 8) cable.
19. Connect the Earth ground wire, if available, to the crimp ring terminal inside the
Mounting Plate. Refer to
Figure 2.4
above.
Note
: The Earth ground is not provided with the VGA-PEND-WPLATE kit; it is a ground
connection made at the installed location.
20. After making the harness connections to the Mounting Plate, rotate the Pendant Arm to
close and tighten the two (2) captive screws to 10-12 N-m (90-105 in.-lbs).
NOTICE!
After all wiring is complete, close the pendant arm over the mounting plate and
tighten the two (2) captive screws on the pendant arm to 10-12 N-m (90-105 in.-lbs).
F.01U.250.238 | 1.0 | 2011.08
Installation Guide
Bosch Security Systems, Inc.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
Содержание VGA-PEND-ARM
Страница 2: ...Available from A1 Security Cameras www a1securitycameras com email sales a1securitycameras com ...
Страница 33: ...Available from A1 Security Cameras www a1securitycameras com email sales a1securitycameras com ...
Страница 34: ...Available from A1 Security Cameras www a1securitycameras com email sales a1securitycameras com ...
Страница 35: ...Available from A1 Security Cameras www a1securitycameras com email sales a1securitycameras com ...
