Bosch VGA-PEND-ARM Скачать руководство пользователя

Страница: 22 / 36

3.3.5

en | Cable and Wire Standards

AutoDome Pendant Arm Mount

Using a Fiber Optic Ethernet Media Converter to Transmit Video and
Control

The fiber optic media converter kit, available for AutoDome 700 Series cameras, is designed

to transmit 10/100 Mbps Ethernet signals over fiber optic cable using 10/100 Mbps Small

Form-factor Pluggable (SFP) modules. The SFP modules are available as multi-mode fiber

(MMF) or single-mode fiber (SMF) models with a single SC connector or dual-fiber with an LC

connector. Refer to the

VG4-SFPSCKT Fiber Optic Media Converter Installation Guide

Ethernet Media Converter

Data Interface

Ethernet

Data Rate

10/100 Mbps

IEEE 802.3 Compliant

Full Duplex or Half Duplex Electrical Port

Full Duplex Optical Port

Fiber Type, MMF

50/125 µm MMF. For 50/125 µm fiber, subtract 4 dB from the

specified optical budget value. Must meet or exceed fiber standard

ITU-T G.651.

Fiber Type, SMF

8–10/125 µm SMF. Must meet or exceed fiber standard ITU-T

G.652.

Maximum Distance

60 km (37.3 miles)

Requirement

Media converter receiver (CNFE2MC/IN) at controller end of

system

Terminal Connection

Duplex LC or Single SC

3.4

Control-only Cables

3.4.1

Controlling the AutoDome via Biphase

(Shielded 2-wire, half-duplex, multi-drop, 5000 ft. cable limit)

Biphase is the standard Bosch protocol used to send Pan/Tilt/Zoom control over 2-wire

shielded twisted pair (STP) terminated with a 100 Ω terminal resistor.

The AutoDome has a 100 Ω termination resistor between the Biphase C+ and C- terminals.

CAUTION!

The Biphase shield must be connected to the head end only.

Cable Type

STP - Shielded Twisted Pair

Distance

1524 m (5000 ft) Belden 8760 recommended

Transmission Rate

31.25 KHz

Gage

1.02 mm (18 AWG)

Termination

100 Ω

Terminal Connector

Screw terminals

Voltage

4 Vp-p

F.01U.250.238 | 1.0 | 2011.08

Installation Guide

Bosch Security Systems, Inc.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Содержание VGA-PEND-ARM





































Результаты поиска

Содержание VGA-PEND-ARM

Отзывы:

Похожие инструкции для VGA-PEND-ARM

Бренды по названию

Популярные бренды

Bosch VGA-PEND-ARM, Руководство по установке

Результаты поиска

Содержание VGA-PEND-ARM

Отзывы:

Похожие инструкции для VGA-PEND-ARM

Бренды по названию

Популярные бренды