Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 85

Страница: 85 / 344

One powerful component supplies other components via the common DC

bus connection.

Components marked with gray background color: Optional, de‐

pending on the application

Component HCS01 (more powerful than component B); con‐

nected to other components via DC bus

Component HCS01 (less powerful than component A); connec‐

ted to other components via DC bus

Bb relay contact wiring

Module bus

Fig. 4-23:

Central Supply

Group supply

●

Option 1:
Several powerful HCS01 components (of the same size!) are connected

to the mains and supply other components via the common DC bus con‐

nection. This requires balancing chokes between supply mains and

components.

Components marked with gray background color: Option‐

al, depending on the application; the choke is used to re‐

duce current harmonics

Component HCS01 (more powerful than component B; all

components A identical); connected to supply mains via

balancing chokes; connected to other components via DC

bus

Component HCS01 (less powerful than component A);

connected to other components via DC bus

Bb relay contact wiring

Module bus

Fig. 4-24:

Group Supply; Several HCS01 Components Connected to

Supply Mains

●

Option 2:
All HCS01 components (of the same size!) are connected to the mains

and interconnected via the common DC bus connection. This requires

balancing chokes between supply mains and components.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

83/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды