Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 55

Страница: 55 / 344

The continuous current of the drive controller should be greater

than the continuous current of the motor.
The continuous power of the drive controller must be greater than

the required average power!

Selecting the Connection Technique

For the available power cables and encoder cables, see documentation

"Rexroth Connection Cables IndraDrive and IndraDyn".

Notes on Commissioning

For further information, notes on commissioning and supporting

documents (e.g., forms for entering the required data) see firm‐

ware documentation.

4.3.5

Cables

Motor power cables

Selection

How to select a suitable motor power cable:
See documentation "Rexroth Connection Cables IndraDrive and IndraDyn"

(R911322949).

Allowed cable lengths

Allowed cable lengths at ambient temperature T

a_work

≤ 40 °C according to

EN 60 204:

HCS01.1E-…-A-02

PWM frequency [kHz]

W0003

40 m

20 m

15 m

5 m

W0006
W0009
W0013
W0018

HCS01.1E-…-A-03

W0005
W0008
W0018
W0028
W0054

75 m

38 m

25 m

Tab. 4-11:

Allowed motor cable lengths

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

53/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды