Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 101

Страница: 101 / 344

HCS01.1E-W0003, -W0006, -W0009, -W0013, -W0018-A-02
Nominal voltage of mains filter: 1 × 230 V

Clock frequency

[kHz]

Leakage capacitance (motor + ca‐

ble)
[nF]

Mains filters

EMC limit value class to be ach‐

ieved

(IEC / EN 61800-3)

4; 8

< 90

NFE02.1

FN350 (Schaffner)

4; 8

90 < … < 120

< 20

20 < … < 40

Only allowed up to a nominal current of 8 A

Tab. 4-38:

Mains filter; 1 × 230 V

HCS01.1E-W0005, -W0008, -W0018-A-03, -W00028, -W00054, (mains voltage: 3 × 400 V, L1-L2-L3)
can be combined with

HCS01.1E-W0003, -W0006, -W0009, -W0013, -W0018-A-02, (mains voltage: 1 × 230 V, L-N)
Nominal voltage of mains filter: 3 × 400 V + N

Clock frequency

[kHz]

Leakage capacitance (motor + ca‐

ble)
[nF]

Mains filters

EMC limit value class to be ach‐

ieved

(IEC / EN 61800-3)

< 70

FN3280H (Schaffner)

70 < … < 120

< 70

FN3256H (Schaffner)

< 40

FN3280H (Schaffner)

40 < … < 70

< 40

FN3256H (Schaffner)

< 20

FN3280H (Schaffner)

This combination allows 3-phase and 1-phase HCS01 devices

to be interconnected at one common 4-phase mains filter.

Thereby, the nominal current of the mains filter and the maxi‐

mum allowed leakage capacitance are taken into account.

Tab. 4-39:

Mains filter; 3 × 400 V + N

Limit Value Classes

IEC / EN

61800-3

CISPR 11

(EN55011)

Explanation

Curves of

limit value

character‐

istic

Category C4,

2nd environ‐

ment

None

One of the following 3 requirements must have been fulfilled: Mains con‐

nection current >400 A, IT mains or required dynamic drive behavior not

reached by means of EMC filter. Adjust limit values to use and operation

on site. User has to carry out and provide evidence of EMC planning.

Category C3,

2nd environ‐

ment

Class A; Group

I > 100 A

Limit value in industrial areas to be complied with for applications operat‐

ed at supply mains with nominal currents > 100 A.

1.1
1.2

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

99/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды