Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 143

Страница: 143 / 344

X9, integrated/external braking resistor

Lethal electric shock by live parts with more

than 50 V!

WARNING

Exclusively operate the device
●

with plugged on connectors (even if there haven't been any lines con‐

nected to the connectors) and

●

with connected equipment grounding conductor!

Function

X9 is used to connect the integrated or external braking resistor HLR. By

means of an internal switch, the braking resistor is connected to the DC bus.

Parameterize the external braking resistor by means of the firm‐

ware to protect the drive controller and the braking resistor

against overload:
●

P-0-0860, Converter configuration

●

P-0-0858, Data of external braking resistor

Connection (HCS01.1E-W0003…

W0028)

Fig. 6-7:

Connecting the braking resistor (HCS01.1E-W0003…W0028)

Connection (HCS01.1E-W0054)

Fig. 6-8:

Connecting the braking resistor (HCS01.1E-W0054)

Notes on installation

Maximum allowed line length to external braking resistor: 5 m
Twist unshielded lines.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

141/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды