Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 53

Страница: 53 / 344

When the inductance is measured, different inductance values

can be determined at different rotor positions within one pole pair

distance of the motor. The average value is relevant for the check

of the minimum value.
Correct values can only be determined when the motor is in

standstill!

Available third-party motor

Planned third-party motor

0.5 × (L

U-Vmin

- L

U-V

) (inductance measurement

with 1 kHz)

Fig. 4-2:

Mounting of 3 × L

(Three-Phase Choke)

Calculate the leakage inductance (asynchronous mo‐

tor) or inductance (synchronous motor) of the third-par‐

ty motor by means of the single-phase equivalent cir‐

cuit diagram (manufacturer's specification!).
Determine choke by means of calculation, if necessary.
It is recommended that you contact Rexroth!

Requirements on the choke:
●

n_Dr

≥ I

n_Mot

The rated current of the choke has to be greater than or equal to the rated motor current.

●

Depending on the maximum speed, the choke is loaded with the respective output frequency and the PWM frequen‐

cy of the drive controller.

●

The insulation class has to correspond at least to that of the motor or has to be sized for higher temperatures.

●

The voltage load of the choke depends on the drive controller used.

Tab. 4-9:

Data for Possibly Required Choke

Temperature Evaluation of Third-Party Motor

Only operate such motors with incorporated temperature sensor at

Rexroth IndraDrive Cs controllers so that the motor can be thermally moni‐

tored by the drive controller and protected against destruction by too high

temperature rise (see "P-0-0512, Temperature sensor").
When, in exceptional cases, you would like to operate third-party motors with‐

out temperature sensor at Rexroth IndraDrive Cs controllers, you must deter‐

mine the thermal time constants of motor housing (P-0-4035) and motor

winding (P-0-4034, P-0-4037). By means of its temperature model, the firm‐

ware can correctly reflect the cooling situation of the motor.

In case the motor housing or fan is dirty, this worsens the cooling

situation of the motor and protection against thermal overload is

therefore insufficient!

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

51/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды