Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 160

Страница: 160 / 344

Ground connection

The ground connection of the housing is used to provide functional safety of

the drive controllers and protection against contact in conjunction with the

equipment grounding conductor.
Ground the housings of the drive controllers:

1. Connect the bare metal back panel of the drive controller in conductive

form to the mounting surface in the control cabinet. To do this, use the

supplied mounting screws.

2. Connect the mounting surface of the control cabinet in conductive form

to the equipment grounding system.

3. For the ground connection, observe the maximum allowed ground re‐

sistance.

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

158/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды