Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 283

Страница: 283 / 344

8.2.11

Hall Sensor Adapter Box (SHL03.1-NNN-S-NNN)

Use

The Hall sensor adapter box "SHL03.1-NNN-S-NNN" (material number:

R911335257) is used to operate linear MCL motors. The Hall sensor adapter

box processes signals of the following systems:
●

Digital Hall sensor

●

Length measuring system

The Hall sensor adapter box transmits the signals for encoder evaluation to

the drive controller.
The housing is made of sheet steel and has the degree of protection IP20.

For detailed information on linear MCL motors, see the documentation

"Rexroth IndraDyn L, Ironless Linear Motors MCL" (R911330592).

Dimensions

Fig. 8-33:

Dimensions

Mounting

Options for mounting:
●

Top-hat rail (TH 35-7.5 according to EN 60715)

●

With 2 screws (M4) to the mounting surface; select the appropriate

screw type and length for the mounting surface

The mounting position can be selected as desired.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

281/341

Rexroth IndraDrive CsDrive Systems with HCS01

Cables, accessories, additional components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды