Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 154

Страница: 154 / 344

How to Remove the Touch Guard:

DC bus voltage

30 Min. !

Before accessing the device, wait at least 30 minutes after

switching off the supply voltages to allow discharging.

With a small screwdriver (blade width < 3 mm), push the fixing

device outwards and simultaneously lever out the touch guard.

Pull off touch guard.

Store the touch guard in a place where you can find it later on.

If you want to operate the device without DC bus connector,

you have to plug the touch guard on connection point X77

again.

Fig. 6-9:

How to Remove the Touch Guard

Fig. 6-10:

DC bus connector at device

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

152/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды