Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 204

Страница: 204 / 344

The encoder signal assignment to the inputs is based on clock‐

wise rotation (front view toward motor shaft).
●

Track A (A+, A-, "cos") advances track B (B+, B-, "sin") 90°

electrically.

●

The actual position value increases (prerequisite: negation

of the encoder signals was not parameterized).

●

If available, the reference track R (R+, R-) provides the refer‐

ence mark pulse at positive signals of track A and track B (in

the so-called "0-th" quadrant).

Standard setting: See Functional Description of firmware.

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

202/341

Rexroth IndraDrive CsDrive Systems with HCS01

Technical data of the components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды